Page 1 of 16 1234511 ... LastLast
Results 1 to 15 of 237
  1. #1
    Joined
    Nov 2001
    Posts
    81

    XP333 WPCRSET/WPCredit Changes, Tweaks, mods and more

    Tweaks have been posted throughout the entire thread..please check out all of the pages for all of the information you will ever need for the XP333..please post anything you come up with in your testing.
    Last edited by Furor; 03-23-2002 at 01:07 PM.

  2. #2
    Joined
    Dec 2001
    Location
    Connecticut
    Posts
    783
    Bump!

  3. #3
    Joined
    Oct 2001
    Location
    Salem, OR
    Posts
    555
    bumpity bump bump*
    Barton 2500+ AQUCA | DFI Infinity Ultra & Modded Abit NF7-S 2.0 | 2x256MB Corsair XMS3502 v1.1 | ATi Radeon 9700 Pro | 2x36GB WD Raptors | Modded TTGI 520SS | Lian-Li PC-67

    20,020 2560MHz, 9700 Pro 383/330
    17,455 3200+, 9700 Pro No OC.

  4. #4
    Joined
    Sep 2001
    Location
    Vega$
    Posts
    1,317

    Good idea Furor!

    K, heres some of the easy ones to get started with...

    When installing the board for the first time, lay the board on a flat firm surface and really shove in the RAM. Installing RAM on this board aint easy

    If needed, set memory voltage to an undocumented 2.8 volts by setting jumpers on pins 2/3 and 5/6 (JP10)

    If Motherboard monitor software(MBM)isnt working correctly, select the KA266 settings

    If benching with Sandra 2002 and have troubles, try disabling DMI/SMBIOS in all the applicable modules

    If too aggressive with jumps in FSB or multipliers etc cause ya to have to reset the CMOS, try booting while holding down the "Insert" key instead. (for me this works most of the time)

  5. #5

    a couple

    Just a couple that I know of,
    when using the 1/5 divider
    78=80

    when using a fsb 166 or higher
    61=6c

    both of these are defaults on the 1/18 bios I believe though

  6. #6
    Joined
    Feb 2002
    Posts
    47

    Noob q's

    OK im a complete noobie to OCing so i have some questions that noobies would ask?

    Where do i get WPCRSET/WPCredit?

    What does it do?

    How do i use it?

  7. #7
    Joined
    Jan 2002
    Posts
    97
    Here are some of the settings I have read about:

    78->C0 or 80 will increase memory bandwidth in bios prior to
    0118 (0118 defaults to CO) above 166mhz. C0 is slightly
    slower than 80 but more stable. Not advisable to change
    from 00 with 2 sticks above around 160mhz fsb

    61->6c needed to allow bios from december up to 0116, maybe
    others, to achieve good memory bandwidth above 166

    7a->7f and some other values that I don't remember increase the
    performance of the ram regardless of the fsb if your memory
    can handle it. Can be highly unstable though.

    This is what I know to date any more?

  8. #8
    Joined
    Jun 2000
    Location
    Texas
    Posts
    542
    Hey cool stuff guys and excellent tips lallend. i can dig using wpcrecit and set but where yah get the pcr for the board?
    Abit AV8 Venice 3000+ rev E @ 2.5 1.4v--- OCZ Plat3700 2 3 3 8 1t--- Chieftec Aluminum 601 --- tagan480 --- Aud2-->Aud2 hack --- WD Raptor(bleh)/Barracuda 160 --- LiteON 52.32.52 --- Mitsu DiamondPRO 22inch --- Swifty cooled EVGA 6800NU 440/949

  9. #9
    Joined
    Jun 2001
    Posts
    7

    pcr

    the pcr file would be greatly appreciated

  10. #10

    no pcr

    From what I know there is no pcr file yet

  11. #11
    Joined
    Jan 2002
    Location
    Italy
    Age
    57
    Posts
    120
    ..you do not need pcr file, simply load the mod you want using wpcrset and that's all, it works!

    Ciao Max!
    DFI LanParty UT NF3 250Gb; 1024mb DDR566 Vitesta A-Data; 2 Maxtor SATA raid0 160gb; Athlon64 3000+@4000+; Liquid Cooled; Pov 6800GT@Ultra; 16X LG Dvd; 8X Mast Dvd; SBLive; Enermax 460W; WinXP Pro SP1; B747 Pilot

  12. #12

    easy

    its definitely not very difficult, about a 30 second job (if that)

  13. #13
    Joined
    Nov 2001
    Posts
    81
    Thanks guys, lets keep this going with some nice information..hopefully kami can share some of his great mods

  14. #14
    Joined
    Oct 2001
    Location
    Salem, OR
    Posts
    555

    ACF *newb tested, OC'er approved*

    For ultimate stability:

    Auto (by SPD)
    Auto (by SPD)
    Disabled
    Disabled
    Enabled
    CAS 2.5 (this is faster than CAS 2 on many boards)
    Disabled
    128 MB or .5 your total memory.
    +7 (yep, its the fastest)
    High
    Disabled.
    1 us
    Disabled.

    Best accompanied with Auto PCI divider for good results.

    I can get into windows @ 195 FSB with these, albeit not stable.
    Barton 2500+ AQUCA | DFI Infinity Ultra & Modded Abit NF7-S 2.0 | 2x256MB Corsair XMS3502 v1.1 | ATi Radeon 9700 Pro | 2x36GB WD Raptors | Modded TTGI 520SS | Lian-Li PC-67

    20,020 2560MHz, 9700 Pro 383/330
    17,455 3200+, 9700 Pro No OC.

  15. #15
    Joined
    Sep 2001
    Location
    Vega$
    Posts
    1,317
    Bump

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •